PChome聯名卡筆筆享最高6%
商品編號:DSACMQ-A9006IXPF
分享
賣貴通報

耐高溫 AB膠 多種材質黏合修補用 50g

$149
$249
折價券
  • 台灣製造
  • 耐高溫 360F
  • 適用各種金屬、管路配件
  • P幣

    【限全盈+PAY】單筆滿$5000送100P幣

  • 登記送

    單筆滿1888元送188P幣

  • 登記送

    單筆滿$350 登記送特大杯冰梔子花青茶單筆滿350元送【電子票券】特大杯冰梔子花青茶

  • 登記抽

    【限APP下單】全站指定品單筆滿888元抽Mio gogoro專用記錄器、國際牌掌上型電鬍刀 (顏色隨機)

付款方式
配送資訊
  • 明早到貨
    北北桃限定 7-11快速到貨
  • PChome 倉庫出貨，24小時到貨
    說明
  • 可宅配到府，滿 $490 起免運
  • 可超商取貨，滿 $350 起免運
  • 可 i 郵箱取貨，滿 $290 起免運
銀行卡、行動支付
優惠總覽
立即查看

搜尋更多

商品詳情
  • PowerBon 多種材質黏合修補用]PLASTIC STEELPLASTIC STEELPLASTIC STEELResin4MinutesWorks on metalsDrill Sand PaintTap MachineFill cracks & chips25各種金屬鑄件、管路配件、桶槽修補黏合用50g
  • 高溫多種材質快速修補用4分鐘型塑鋼膠是一種高分子油灰狀 )產品AB兩劑強迫混合快速硬化操作時間急迫可在緊急情況下快速修補黏合,完全硬化後,硬度特佳,耐高溫360,防水不生鏽,可抗大多數化學侵蝕。可行車、削、磨、鑽,絕緣(不導電,可上漆。適合用途金屬鑄件沙眼、桶槽、油箱、水箱、管路配件、機械、模具之修補。任何金屬製品損壞、撞痕、孔洞、斷裂、玻璃、石材、陶磁、碳維、木材、玻璃纖維、居家水泥裂縫、大理石掉落、電器製品、藝品、裝飾、模型、釣具、玩具、汽機車零件、運動器材,均可修補黏合。PowerBon4 minutes rapid Plastic Steel Epoxy is twopartepoxy adhesives Resin and hardener arefced to mix and harden rapidly After fullhardening, it has excellent hardness andendures 360°F Its paintable, antirust,waterproof, resistant to most of weak chemicalsand has insulation property You can millshave, sand and drill after it fully hardensAPPLICATIONS: It cures fast for quick metal tometal bonding and repairs, suchfilling casting blister, water tank, oil tank, pipe,gap fillingmachine, mold, and many materials withcracks,breaks and holes, such as glass, stone,carbon fiber, wood, fiberglass, crack of wall,marble leakage, electrical appliance, craft,adornment,model, fishing tackle, toy, autopartsBONDS SKIN EYE IRRITANT STORAGE CAREFULLY VENTILATION DRY IRRITANTRECYCLE皮膚接著注意眼入注意 保管注意使用方法:要通風儲存陰涼處刺激性環保回收1將欲修補黏著的表面用砂紙磨予粗糙,確保表面潔淨乾燥。2旋轉蓋子,用蓋子頂端的針狀物將金屬封口刺穿,不要捏緊瓶身,以免膠水大量溢出。3擠出同等量的A、B兩劑,均勻攪拌混合。混合比例 1:1,誤差大或混合不均勻會造成硬化不良。4. 請在3分鐘之內完成黏合固定作業。4分鐘硬化,最佳黏合強度須經24小時。氣溫低於10°C以下則硬化時間較長。】注意事項:請戴護具施工,誤觸皮膚時,請用肥皂和清水剝離或用(乙醇)酒精擦拭即可,誤入眼睛時不可搓揉,立刻用大量清水沖洗數分,且就醫診治,若誤食立刻送醫治療。【存放兒童取不到的地方】不當的使用,可能會造成物品受損,務必事先測試接著物材料,測試滿意才使用本產品進行施工黏合。未適當使用及操作本產品,造成任「何直接或間接及偶發傷害,不負任何之責任。主要成份:高分子環氧樹脂、聚醯醇樹脂。產品規格:兩劑型鋁軟管包裝,重量50g±5%DIRECTIONS FOR USE:1.Roughen the surfaces to be joined or repaired withsandpaper. Ensure surfaces are clean & dry, free from dirt,oil, moisture, rust.2.Remove caps. Pierce the ends of tubes with points oncaps. Be careful to avoid spilling of adhesive when piercing.3.Squeeze equal amount of Resin & Hardener onto a cleansurface. Mix thoroughly. Mix ratio=1:1. Wrong ratio orunequal mixing may result in bad hardness.4.Finish the whole operation within 3 minutes. Solidify in 4 minutes. Full bond strength is reached after 24 hours.[when the temperature is below 10, the hardening time islonger.CAUTION: Irritation for eyes, skin, respiratory system. Previousprotection is recommended. For skin contact, wipe offcontamination and wash thoroughly with soap and warmwater.In case of eye contact, rinse with plenty of warm waterand get prompt medical attention. If swallowed, seek the physician.(KEEP OUT OF REACH OF CHILDRENImproper use may damage the surface. Be sure to test onan inconspicuous area in advance. Testing satisfactionbefore formal use is a must. The company accepts noliability for any damage caused by improper use oroperation of this product.Contains:Epoxy Resin, Polymercaptan.Made in Taiwan
購物須知

別人也看了