PChome聯名卡筆筆享最高6%
商品編號:DSACMQ-A9006IXOS
分享
賣貴通報

耐高溫 AB膠 凝膠狀快速黏合用 50g

5.0
1則評價
$135
$299
折價券
  • 台灣製造
  • 修補、黏合、密封、防水...
  • 凝膠狀、不垂流
  • P幣

    【限全盈+PAY】單筆滿$5000送100P幣

  • 登記送

    單筆滿1888元送188P幣

  • 登記送

    單筆滿$350 登記送特大杯冰梔子花青茶單筆滿350元送【電子票券】特大杯冰梔子花青茶

  • 登記送

    【限APP下單】全站指定品單筆滿888元送88P幣

  • 登記抽

    【限APP下單】全站指定品單筆滿888元抽Mio gogoro專用記錄器、國際牌掌上型電鬍刀 (顏色隨機)

付款方式
配送資訊
  • 明早到貨
    北北桃限定 7-11快速到貨
  • PChome 倉庫出貨，24小時到貨
    說明
  • 可宅配到府，滿 $490 起免運
  • 可超商取貨，滿 $350 起免運
  • 可 i 郵箱取貨，滿 $290 起免運
銀行卡、行動支付
優惠總覽
立即查看

商品評價

5.0
共 1 則評價
5.0
100%
4.0
0%
3.0
0%
2.0
0%
1.0
0%
最相關
吳**
2024/04/29

搜尋更多

商品詳情
  • 耐高溫 凝膠狀快速黏合用 adhesivesGEL NON-DROPEPOXYResinMinutesRapid金屬 METAL石材 STONEHardener MinutesEPOXY陶瓷 CERAMC玻璃GLASS玻璃纖維 IBERGLASS木材WOOD25mlPowerBon 多用途緊急、修補、填縫、黏合耐高溫 | 凝膠狀快速黏合用4分鐘型AB膠是一種AB兩劑強迫混合快速硬化黏合劑操作時間急迫。完全硬化後可防水。耐溫320F且抗大多數化學侵蝕絕緣(不導電, 可上漆用途說明:金屬、玻璃、石材、陶瓷、碳纖維、玻璃纖維、木材、硬質皮革、硬質塑膠(PVC,ABS,PS)。居屋水泥裂縫、磁磚、大理石掉落修補粘合、電器製品、藝品、裝飾品、模型、釣具、玩具、汽機車零件、運動器材等,均可快速修復黏合。不適用材質:聚乙烯、、氟素樹脂、矽膠、泡棉50 gPowerBon4 minutes rapid EPOXY Adhesives consistof two components Resin and hardenerare forced to mix It hardens rapidly. Afterfull hardening, it is waterproof, endures320 F,resistant to most weak chemicals,paintable.APPLICATIONS: Metal, glass, stone,ceramic, fiberglass, fiber carbon, wood, rigidleather, rigid plastic (PVC, ABS, PS).Rapid repair for cracks of wall, marbleleakage, electrical appliance, craft,adornment, model, fishing tackle, toy, partof car, sport appliance etc.Unsuitable: PE,PP, Fluororesin, Siliconeplastic, foamBONDS SKIN EYE IRRITANT STORAGE CAREFULLY VENTILATIONSTORE IN COOL& DRY PLACEIRRITANTRECYCLE皮膚注意 眼入注意 保管注意使用方法:要通風儲存陰涼處激性環保回收1.將欲修補黏著的表面用砂紙磨予粗糙,確保表面潔淨乾燥。2.旋開蓋子,用蓋子頂端的針狀物將金屬刺,不要緊捏瓶身,以免膠水大量溢出。3.擠出同等量的A、B兩劑,混合。混合比例1:1,誤差大或混合不均勻會造成硬化不良。】4. 在3分鐘之完成黏合固定作業。4分鐘硬化,最佳黏合強度須經24小時。氣溫低於10以下則硬化時間較長】注意事項:請戴護具施工,皮膚時,請用肥皂和清水搓揉或用(乙)酒精擦拭即可,誤入眼睛時不可搓揉,立刻用大量清水沖洗數分,且就醫診治,若誤食立刻送醫治療。存放兒童取不到的地方】不當的使用,可能會造成物品受損,務必事先測試接著物材質,測試滿意才使用本產品進行施工黏合。本產品廢棄處理方式,須在政府核可廢棄物處理設施處理。主要成分:環氧樹脂、聚醯醇樹脂。產品規格:兩劑鋁軟管包裝,重量50g±5%®PowerBon co., LTD.DIRECTIONS FOR USE:1. Roughen the surfaces to be joined or repaired withsandpaper. Ensure surfaces are clean & dry, freefrom dirt, oil, moisture,rust.2. Remove caps. Pierce the end of tubes with pointson caps. Be careful to avoid spilling of adhesivewhen piercing.3. Squeeze equal amount of Resin & Hardener ontoa clean surface. Mix thoroughly. 【Mix ratio=1:1.Wrong ratio or unequal mixing may result in badhardness. )4. Finish the whole operation within 3 minutes.Solidify in 4 minutes. Full bond strength is reachedafter 24 hours. 【When the temperature is below 10C,the hardening time is longer. ICAUTION:Irritation for eyes, skin, respiratory system. Previousprotection is recommended. For skin contact, wipe offcontamination and wash thoroughly with soap and warmwater. In case of eye contact, rinse with plenty of warmwater and get prompt medical attention. If swallowed,seek the physician.【KEEP OUT OF REACH OF CHILDREN】Improper use may damage the surface. Be sure to teston an inconspicuous area in advance.Be sure to dump the waste in a permitted environmentunder the law.CONTAINS :Epoxy Resin, Polymercaptan.Made in TaiwanITEM NO: 3337
購物須知

別人也看了